What should I do if my water heater pilot light keeps going out?
The solution: First, cut off the gas supply, switch off your heater, and wait for the thermocouple to cool off. You’ll have to manually bend or straighten the thermocouple back to position.
Why does my gas water heater keep going out?
If you can light your pilot light, but it keeps going out, the first item to check is the thermocouple. When the water heater is first lit, a valve releases gas into the burner, and the pilot light ignites that gas.
Why does my water pilot keep going out?
Therefore, a dirty thermocouple might be the reason why your water pilot keeps going out. A layer of dirt and grime can hinder the electric current from reaching the thermocouple. As a result, the gas supply will be cut off and the pilot light will go out.
Why does the pilot light on my furnace keep going out?
The thermocouple is the copper rod the pilot flame directly hits. Sometimes it’s referred to as the “flame sensor.” It’s a safety mechanism that shuts the gas off should the pilot go out. If the thermocouple fails to shut off the gas, all the gas flowing through the furnace could get into your home.
How does a pilot light go out on a water heater?
Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. Your thermocouple is responsible for sensing when your pilot light is lit. If it senses that the pilot light has gone out, the thermocouple shuts off the gas supply to the flame in order…
How do I check the pilot light on my water heater?
Open the door/cover over the pilot light access. This will be located under the gas valve; some water heaters just have an open gap instead where you can see the pilot light burner. Use a flashlight or a headlamp to find the burner inside. Two small gas tubes will lead to it.
How do you light the water heater pilot?
Turn the gas knob to “Pilot,” press and hold it down. This will start the flow of gas so you can light the flame. Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold.
Why water heater pilot does not stay on?
When it will not stay lit it is a sign of a defective ‘thermocouple’. The thermocouple senses heat from the pilot light and sends a signal back to the gas valve. When they fail the gas valve will not open. See the discussion on ‘gas water heater thermocouples ‘ for more information.
Why does my pilot light keep going out?
If your pilot doesn’t re-light, won’t stay lit or keeps going out after a short time, you most likely have an issue with the hot water heater thermocouple. This can happen with age. This can happen with age.
Where is the pilot light on a gas heater?
The pilot light should be close to the gas burner tube, watch it closely. Ignite the flame with a long match while switching the knob to “pilot,” hold it in the position for 35 seconds. Once the pilot comes on, turn the knob back to “on.”
The pilot in my gas water heater (Aquamax 205) has been going out sporadically over the last 2 weeks. Yesterday, I replaced the thermocouple with a universal thermocouple and cleaned out the dust and soot from the burner area. After installation, I also did the detergent test to make sure the gas connections are secure and not leaking.
Why does pilot light keep going out?
Why Does My Pilot Light Keep Going Out. The number one reason why the pilot light keeps going out is the thermocouple. Either the thermocouple is going bad or it is dirty and needs to be cleaned. Thermocouples work by producing a small amount of voltage when it is heated. This is the pilot flame that provides the heat. Nov 23 2019
Why is my pilot light not staying lit?
The primary reason a pilot light won’t stay lit is simply equipment malfunction. If you’ve checked everything else and the light continually goes out, this is probably the cause. In this case, you may need to replace your pilot light. A pilot light can also keep going out because of a problem with the thermocouple .
Why does your pilot light go out?
However, if the light goes out frequently there could be other issues. Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds.
Why is my furnace pilot not staying lit?
The most common reason the furnace pilot light won’t stay lit. Bad Thermocouple. A furnace thermocouple is a safety feature that regulates gas flow to your system based on whether the pilot light is on. In simple terms, the thermocouple checks to see if your pilot light flame is lit and turns off the gas flow if it senses that your pilot light is off, so you don’t have gas building up in your home.
What happens if the pilot light is not lit?
Once the thermocouple detects that the pilot light isn’t lit, it turns the gas off as a safety measure. An unlit pilot can also stem from a dirty thermocouple as the dirt may be obstructing the current signal, which would also lead to a gas outage.
What to do if your hot water tank won’t stay lit?
Here’s a solution for your hot water tanks that won’t stay lit!! There are other tanks that have light sensors, flame sensors and someone, if that’s yours this will still work. You’ll have to make sure the other sensors on your tank are all working though. This can be accomplished with a $10 multi metre and basically zero knowledge of electronics.
Why does my pilot light keep going out on my hot water tank?
Insufficient gas in the tank is one reason for the pilot light to stop remaining lit, because while there might be enough gas trickling through the line for a tiny flame, once the burner kicks in the flame goes out because of insufficient gas. Also ensure that all the valves on the line to the heater are open so that gas is getting to the pilot.
Why is the water heater pilot light keeps going out?
There are several things that can cause your gas water heater pilot light to keep going out. One of the most common is your thermocouple. If you are unfamiliar with what this device does, the thermocouple is a device in your hot water heater that uses an electrical current to determine whether the pilot light is on or not.
The solution: First, cut off the gas supply, switch off your heater, and wait for the thermocouple to cool off. You’ll have to manually bend or straighten the thermocouple back to position.
Therefore, a dirty thermocouple might be the reason why your water pilot keeps going out. A layer of dirt and grime can hinder the electric current from reaching the thermocouple. As a result, the gas supply will be cut off and the pilot light will go out.
Once the thermocouple detects that the pilot light isn’t lit, it turns the gas off as a safety measure. An unlit pilot can also stem from a dirty thermocouple as the dirt may be obstructing the current signal, which would also lead to a gas outage.
The pilot light should be close to the gas burner tube, watch it closely. Ignite the flame with a long match while switching the knob to “pilot,” hold it in the position for 35 seconds. Once the pilot comes on, turn the knob back to “on.”
Why is my Rheem water heater not making hot water?
If the unit still doesn’t make enough hot water, it is either undersized for your needs, partially filled with mineral sediment or has a plugged gas valve. A Rheem technician can check the gas valve and clean or replace it.
What to do if your gas water heater is not lit?
Gas water heater: If your unit has a pilot light and it isn’t lit, follow the instructions in your user’s manual to relight the pilot using the BBQ lighter. If the unit has an electronic ignition and it won’t fire, the ignition might require replacing.
What to do when pilot light goes out on Rheem water heater?
If the pilot light goes out when you release the red button, repeat steps four and five. If you smell gas at any time while you are lighting your Rheem water-heater pilot light, leave your home immediately and call your gas provider’s emergency phone number from another location.
Why does my water heater pilot light keep going out?
If you cannot hear a subtle gas sound underneath, you may need to call a technician to troubleshoot your water heater. Reassemble the water heater and check back later if the pilot light keeps going out and if you have hot water.
Gas water heater: If your unit has a pilot light and it isn’t lit, follow the instructions in your user’s manual to relight the pilot using the BBQ lighter. If the unit has an electronic ignition and it won’t fire, the ignition might require replacing.
What are the most common problems with a Rheem water heater?
Here’s a list of the most common Rheem water heater problems to look for. Solutions requiring multiple steps are found below. A tripped circuit breaker will shut down an electric heater and gas models that use electricity. Gas: Check if the gas valve has been turned off.
