What should I do if my hot tub Wont Stop Running?
Turn the breaker or power off for a minute and turn it back on again without pressing any of the controls or buttons. The tub should start up at a default 100F temp setting and start a 1-3 hr filter cycle with the pump running low speed until the filter cycle ends or longer if still heating.
How old is the motor on my hot tub?
That said, the hot tub and pump are over 9 or 10 years old, so it must be time for a new motor. I checked the voltage coming from the control panel to the pump (both high and low speed) and got 0.
Why does my hot tub keep running at 108f?
If the display says 108F and the water is actually that temp. and the “heat on” symbol/light shut off on the display at the set temp. of 100F…. Then you have a circuit board that is continuing to power the heater after it supposed to shut off. That would mean a bad board.
Is it possible to destroy a hot tub?
Taking care of a hot tub nowadays is not too difficult, but if you’re not careful, small slips can cause big problems. Most of these won’t DESTROY your hot tub, that’s just my attention grabbing headline, but any of these will cause minor to major problems, which are best avoided.
What happens if you buy the wrong hot tub?
For many first time hot tub owners, picking the right hot tub can be a real challenge. Buying the right hot tub can lead to years of enjoyment with little work while buying the wrong hot tub can be costly, disappointing and irritating. That’s why we’ve compiled this list of 7 common hot tub buying mistakes.
When to buy a hot tub from a reputable dealer?
When you buy a hot tub from a reputable Hot Spring dealer, your package includes access to a wealth of expert knowledge and certified technicians who can ensure the best possible outcome when your spa experiences problems. So, plan a visit to your showroom today.
When is the best time to troubleshoot your hot tub?
For issues that require expert troubleshooting, your Hot Spring dealer is always ready to step in. The best time to start thinking about spa maintenance and repair options is before you even purchase your hot tub.
Why does my hot tub motor not start?
Once you have started it manually the motor, it will continue until the next shut down, but it won’t start automatically again. It’s not the control panel, because you hear the click, which is the message the control panel is sending to the board relay, and the click indicates it should be sending electric to the motor.
Why does my hot tub control panel keep blinking?
If there is any condensation, dry it off. A blinking red light on the control panel may indicate it needs to be reset. For most models, you will need to turn off the power to the spa for a minute or two and then turn it back on again. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.
What does it mean when your hot tub is not heating?
In this case, your control panel topside may show LF or FLO (or a similar flow message). This means there is an issue with water flow, and not enough water is passing through the heater. As a safety feature, the heater should be designed to cut out so it doesn’t burn out.
What to do if your hot tub control panel is dead?
This is why it is important to keep the control panel in good working order. Check out hot tub controls on Amazon. If part of the control panel is dead or the whole panel is frozen, you will want to see if the problem is the circuit board or the control panel.
Why is my hot tub not heating up?
Hot tubs utilize a water pump to move water through the heater and back into the tub. A problem with the water pump can result in the water not getting heated. A dirty filter in the water pump is a common cause of heating problems in hot tubs.
What should you put your hot tub on?
What Can I Put My Hot Tub On? Cement Pad. One of the most common bases used for a freestanding hot tub is a concrete pad. Wood Deck. If you don’t want a freestanding hot tub in the middle of your yard, you may also place it on a deck. Gravel. If you’re looking for a budget-friendly base for your hot tub, gravel is an ideal option. Pavers.
What are the power requirements for a hot tub?
Most hot tubs will require 4 wires being two hot wires, one neutral wire and one ground wire. The most common voltage requirement is 240 volts and most will need a 50 amp circuit.
