What does the topside Control Panel on a hot tub do?

And that’s all the topside control is – a control panel, think of it as a remote control for your hot tub, wired into your spa controller, which is really the brains of the spa system. The spaside control panel, it’s just a convenient way to turn things on and off, and view equipment status lights and water temperature.

What to do if your hot tub topside light is not working?

Another panel problem may be burned out backlighting bulbs. These bulbs can easily be replaced. With the power off, gently pry up the topside control panel with a screwdriver. Next, locate the gray bulb holes in the back of the panel.

Why is my hot tub control panel not plugged in?

If you have some other issues with your hot tub topside control panel, here are some other possible ways to troubleshoot the problem. Your control panel may not be plugged in. Check your connections to make sure that it’s secure and tight. You may have selected the wrong panel.

How do you remove the control panel from a hot tub?

Remove the spa access panel and take the cover off of the control box and unplug the wire that goes form the topside panel to the circuit board. Gently remove the topside control panel. Remove the plastic from the self-stick backing of the topside controller.

How do you remove the topside Control Panel on a hot tub?

First, turn off the power to the unit. Remove the spa access panel and take the cover off of the control box and unplug the wire that goes form the topside panel to the circuit board. Gently remove the topside control panel. Remove the plastic from the self-stick backing of the topside controller.

Why is my spa topide control panel not working?

But there are some ways to reduce the risk… read on. Bottom line is – it could be a bad spaside control panel, or it could be a bad spa control board, or a bad cable that runs between the control panel and the control board. Or it could be fuse on the circuit board or the transformer, not sending the correct power to the topside panel.

When to replace a hot tub control panel?

Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working and connect it to the circuit board. Once you have tested the control panel and it does not work with one you know is in working condition, you may need to replace the circuit board.

Can a hot tub control panel be replaced?

Replace the control panel – If all else fails with your control panel then you might need to just bite the bullet and replace it. The process of replacing a control panel is relatively easy as they are essentially plug and play, you just need to make sure that you get an exact replacement.

Can a spa topside control work with a TV remote?

Topside controls will only work with a particular spa system control board (s). Another TV reference would be appropriate; you have to use the TV remote that is made for your make and model of television. It’s the same with spa topside controls, they only work with the spa control make and model for which they were designed.

What should I know about my spa control panel?

Safety is key when servicing any spa or spa control panel. Remember, safety comes first for you. Please take all necessary precautions before attempting any repairs. Wiring checks are the first step to ensure safety and proper function before beginning service on a unit. A Topside Control Panel activates functions at the touch of a button.

How does the hot tub control panel work?

The hot tub control panel is like a timer that keeps the spa’s temperature constant. It turns off the spa when you forget to and troubleshoots problems. Thus, it is very important to have a spa control system in good working condition. Many issues could face your spa, including electrical issues.

Are there any replacement hot tub control systems?

Replacement spa control systems and packs to get your hot tub running smoothly. We have topside controls, Waterway, Hydrpquip, Balboa, and more!

What to do if your hot tub control panel is dead?

This is why it is important to keep the control panel in good working order. Check out hot tub controls on Amazon. If part of the control panel is dead or the whole panel is frozen, you will want to see if the problem is the circuit board or the control panel.

Is the spa topside control panel returnable?

Since spaside panels are not returnable, this entails some risk on the spa owner. But there are some ways to reduce the risk… read on. Bottom line is – it could be a bad spaside control panel, or it could be a bad spa control board, or a bad cable that runs between the control panel and the control board.

What kind of light is in a hot tub?

Hot Tub Light | Hot Tub and Spa Lights, Light Kit and LED Light. — Hot Tub Warehouse

Which is the best LED light for a spa?

Idealife’s Magnetic Submersible LEDs for spas have an IP68 rating. This means that the light is deemed strong enough to withstand everything from dirt, dust, sand, and water. They have been made waterproof for up to 20 meters underwater so nothing is able to damage the bulb.

How do you replace a top side SPA control panel?

A sticker is typically on the side indicating a part number from the manufacturer. Otherwise, get the number for your spa control pack and call the manufacturer to find out which top side panel will work for you. Replacing a topside control panel is a fairly simple process. First, turn off the power to the unit.

Where can I get replacement parts for my hot tub?

Hot Tub Warehouse is equipped with almost any conceivable spa part you may be in search of. Whether you need a major replacement part like a heater or pump, or are searching for something small like a gasket or O-ring, we have them in stock and ready to ship.

What are the control panels on the artesian hot tub?

This is the original topside that comes with overlay. 4 buttons are Warm Cool Lights Jet 11-0135-77 is the included 4 button Resort Spas colorful overlay (not… Artesian Control Panel K-4 model OP33-0400-40 is available at Hot Tub Outpost.

How big is the South Seas hydrotherapy spa?

Dimensions, capacities and weights are approximate. Specifications are subject to change without notice. Spa images have been digitally rendered and may or may not show optional features. 735B/L: Special Spa Equipped with Pillowfall, Dynastar LED, Ozonator, and Full Foam | *Required by law for certain States.

What to do if your hot tub control panel is not working?

As a first step, reset your breaker. If the problem persists, turn the breaker off and disconnect the panel to examine the circuit board. Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working and connect it to the circuit board.

What does blinking red light on hot tub control panel mean?

Blinking Red Light. A blinking red light on the control panel may indicate it needs to be reset. For most models you will turn off the power to the spa for a minute or two and then turn it back on. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.

How to troubleshoot a spa side control panel?

Spaside Control Panel Buttons Not Working Correctly 1 Check for moisture under glass or on contacts 2 Check cable for any rodent damage, crimping or melting 3 Clean plug-in cable connections at both ends 4 Membrane or touch pad buttons may be faulty 5 Inspect circuit board for damage and correct power output 6 Replace topside control

Why is my hot tub control panel not working?

Once you have determined that proper voltage is running through the circuit board and transformer, continue to the topside control panel. A panel that is not functioning properly may include the following symptoms: low voltage such as missing or scrambled segments, missing icons on the LCD, non-functional LED’s, or non functional buttons.

Examine the panel to see if any moisture is inside the display. See if the panel or any buttons are cracked or if it could have possibly gotten wet. If only part of the control panel is not working, check for any blinking lights or error messages.

Is there a touch screen on my hot tub?

The touch screen control panel is featured on the following Master Spas products Twilight Series Hot Tubs, Michael Phelps Legend Series Hot Tubs, Michael Phelps Signature Swim Spas, and most H2X Swim Spas. Although the size and shape of these panels may look different they all operate the same.

Replacement spa control systems and packs to get your hot tub running smoothly. We have topside controls, Waterway, Hydrpquip, Balboa, and more!

How to troubleshoot a hot tub or spa?

While each brand of hot tub or spa will have a slightly different set up and circuit board, there are common ways to troubleshoot problems. You may have a display on your control panel that will show error codes, which will be very helpful if you have your user manual handy.

What to do if your Spa circuit board is not working?

When your hot tub or spa is not working like it should, the circuit board is one of the first things to check. If it turns out it is working fine, then you can move on to other systems in your hot tub. The first thing to do, just like with your old personal computer, is to turn off the spa and turn it back on.

How do I unlock the hot tub control panel?

However, there are a few steps that are similar if not the same for every hot tub. So, in order to unlock the control panel, users should find and press the “Time” button located on the hot tub’s operating panel. Then, the “Jets 1” button should be pressed followed by the “Set Down” button.

Is there a reset button on a hot tub?

Is there a reset button on a hot tub? Hot tub control panels do not have reset buttons, but their spa heaters can be reset using a button. In order to fully reset the control panel, users should manually turn it off or unplug it and wait 10 to 20 seconds. However, to reset the heater, users can simply use the high-limit reset button.

How to troubleshoot hot tub topside and spa control?

Check the temperature has not been locked. Ensure the buttons are only being pressed lightly. If you can’t sort the problem then check topside is pugged into the circuit board correctly (turn spa off) – if it is then remove decal and check buttons – if they work replace decal / sticker if no control call the proffessionals .

What to do if your hot tub touch pad is blank?

There are no serviceable parts inside the potting that seals the unit. If you still see symptoms of low voltage, such as a sluggish, blank or partially blank panel, or if the display or the LED’s do not function at all, turn the power off and replace the circuit board. My touch pad is blank?

Where is the spa controller on a hot tub?

Locate the digital spa controller. Unclip and remove the grey ribbon cable connecting the digital spa side control where it connects to the spa controller. The top side control is usually secured to the spa shell by either a dual-sided adhesive gasket or by silicone.

What to do if your hot tub topide is not working?

If any of these symptoms are present, perform the following: Turn the power off and unplug the panel from the circuit board. If you have a intermittent fault then it maybe moisture at the PCB connection, dry it out, this may easily sort the problem. Repair of electronic spa sides is usually accomplished by replacement.

Can a universal hot tub control system be replaced?

These spa packs are built to last. They will replace brand name spa equipment in small or large hot tubs with all the reliability you would expect. The hot tub controls are flexible enough to replace different heater placement including LOW FLOW with different heater lengths, controlling multiple pumps.