What does an error code on Sundance spa mean?
Indicates that the flow switch is malfunctioning. The system is disabled in this case and system startup has shorted or has a closed flow switch in this situation. Contact the dealer or a service technician. Indicates that spa needs a new UV bulb. Purchase new UV bulb from dealer and reset countdown timer.
What does Flo code mean on Sundance heat pump?
I found it easily at the Sundance site online and keep a copy on my computer for reference. Nine times out of ten, a flo code means the pressure switch isn’t working, and ergo your circa pump wont work right, nor usually the heat. It’s a cheap part and won’t take a repair guy more the 20 minutes to fix.
How much is the app for Sundance TV?
Was going to try the Sundance TV or Sundance Now app as a lot of their programming is not available on our Suddenlink lineup. We downloaded the Sundance Now app but immediately removed it when we saw it would cost $6.99 a month.
What does summer logic mean on a Sundance spa?
These are the error codes and display messages that a Sundance® Spa may display, along with what they mean and any actions required: “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather.
What are the error codes on the spa side?
Flow Switch (heater is deactivated. Pump may also be deactivated). Panel sensors have been pressed too many times in a short period of time. Circuit Board temperature has exceeded acceptable limit. Freeze protection. No action is necessary. Freeze protection. No action is necessary. Communication between the panel and circuit board is faulty.
How can I tell if my Sundance spa filter is defective?
The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.
What is the National Electrical Code for Sweetwater?
7)ELECTRICAL SUPPLY:The electrical supply for this product must include a suitably rated switch or circuit breaker to open all ungrounded supply conductors to comply with section 422-20 of the National Electrical Code, ANSI/NFPA 70.
What is the error code on the Sundance Spa hot tub?
Sn1 Error Code: Heater is deactivated. High-limit sensor located in the heater drywell is nonfunctional. Sn3: Heater is deactivated. Main temperature sensor located in filter bucket is nonfunctional. 6. ILOC Error Code ILOC Error Code: Hot Tub is deactivated.
Where to find support base for Sweetwater hot tub?
Read and carefully follow the requirements for your hot tub’s support base (found in the section titled, “Locating Your Sweetwater Hot Tub”, page 8).
Is the Sweetwater hot tub covered by warranty?
Damage caused by exposing the hot tub to this abuse is not covered by warranty. We recommend that you always keep the hot tub full of water when it is exposed to direct sunlight and that you keep the Sweetwater insulating cover in place at all times when the hot tub is not in use.
The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.
What causes Flo error message on Sundance Altamar spa?
I have a Sundance Altamar spa, and I’ve occasionally had that FLO error message too in the past. If I recall it might have been caused by air in the lines (not filling tub properly?) or possibly from obstruction. I had one of the small cotton intake covers get sucked into pipes before.
What happens when Sundance spa goes into watchdog?
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
When the spa goes into the Watchdog the spa will not operate. This is how it happens: When you try to use the spa, you will see 3 or 4 dashes on the control panel (depends upon the model). If you try and reset your breaker, sometimes it comes on but it will probably go back into Watchdog error – – – -.
What to do if the main pump is off in Sundance spa?
If debris is present, remove debris, install switch and test system. If condition still exist, replace switch.) if switch measures infinite (no continuity) with pump off, switch is OK, Turn on Main pump and measure across switch terminals for continuity. If continuity is measured, switch is OK.
What does FL1 code mean on a spa heater?
When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock problem at the circulation pump intake.When FL2 code starts flashing it means the flow switch isn’t working and it is stuck closed. In both cases, the spa heater will deactivate.·
What causes a FL2 error code on a hot tub?
Generally speaking, an FL2 error code is caused by one of two components, and for three different reasons. The first reason would be that the flow switch/pressure switch has failed and is delivering a closed circuit at all times.
I have a Sundance Altamar spa, and I’ve occasionally had that FLO error message too in the past. If I recall it might have been caused by air in the lines (not filling tub properly?) or possibly from obstruction. I had one of the small cotton intake covers get sucked into pipes before.
Why does my Sundance spa go into Oh error code?
Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code
I found it easily at the Sundance site online and keep a copy on my computer for reference. Nine times out of ten, a flo code means the pressure switch isn’t working, and ergo your circa pump wont work right, nor usually the heat. It’s a cheap part and won’t take a repair guy more the 20 minutes to fix.
What do you need to know about the Sundance spa?
As you surrender ot the warm, bubbly water of a Sundance® spa, you’ll be whisked away by the right blend of heat, buoyancy and massage that will change thehway you fee. Our patented Fluidix® jets were co-developed with Bowels Fluidics Corp, experts in the field of Fluid Dynamics.
Do You need cover guy for Sundance Hot Tub?
If you are needing a replacement hot tub cover for your Sundance® Spa The Cover Guy is your answer. With all Sundance® Models on file The Cover Guy can easily provide you with a new hot tub cover without you having to measure. The Cover Guy Sundance® Replacement covers are the best made covers at the best price available.
Do you need a cover guy for a Sundance spa?
If you are needing a replacement hot tub cover for your Sundance® Spa The Cover Guy is your answer. With all Sundance® Models on file The Cover Guy can easily provide you with a new hot tub cover without you having to measure.
Why do I get DPC watchdog violation error in Windows 10?
DPC Watchdog Violation errors were very common when Windows 10 was first released—so much so that Microsoft had to release an update to tackle it. Originally it was caused by an SSD driver that was found to be incompatible with Windows 10, and it’s actually a repeat of an issue that occurred in Windows 8 when that was released, too.
Is the heater disabled on a Sundance spa?
OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. This must be repaired only be a Sundance Spas dealer or qualified service technician. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional.
