How to remove potterton ep2002?
There is a rectangular slot on the lower edge on the right hand side. Insert a large flat screwdriver and push upwards, the panel will hinge from the bottom and lift off the wall plate exposing live terminals.
How do I uninstall Potterton EP2000?
Simple turn of the power to the central heating system and make sure you have isolated with the correct switch or fuse. Once you are sure the electricity is off you can release the retaining clip which engages in a small slot. You will need to gently press the tongue in to pivot off the old EP2000.
How do you set a Potterton EP2000 timer?
Press and hold down the STEP & + button, then after 5 seconds, release the 2 buttons. The built-in times are now reinstated. Move slider to SET. Adjust ON1 time, using – & + buttons 1.4 Press STEP button.
How do I replace Potterton EP2002?
There isnt a direct replacement for the EP2002, so you will need to change the back plate, which means to swap the programmer over you need to terminate the wires on the new back plate. The EP2 is sufficient for your needs, but you can chose any CH and HW programmer, you dont need to stick with a Potterton.
How do I set the timer on my Potterton EP2002?
To set up your own ON/OFF times for your model, refer to section 1.3, 2.3 or 3.3 overleaf. If you wish to return to the built in time periods, after charges have been made to them, simply: Ensure the slider is in RUN position. Press & hold down the + button.
Why is my boiler timer not working?
There are a few reasons your timer clock may have stopped working. The clock resetting due to the power being out for a while (especially if you have an older boiler) A blown-out fuse. Your room thermostat settings telling the boiler not to come on.
How do you replace an ep2000 programer Potterton?
Once you are sure the electricity is off you can release the retaining clip which engages in a small slot. You will need to gently press the tongue in to pivot off the old EP2000. Simply reverse the procedure to refit the new EP programmer replacement.
How to replace a Potterton central heating programer?
How do you replace an EP Clock in Potterton?
Once you are sure the electricity is off you can release the retaining clip which engages in a small slot. You will need to gently press the tongue in to pivot off the old EP2000. Simply reverse the procedure to refit the new EP programmer replacement. The replacement EP clock is a fast to fit direct replacement which is simple to fit.
Why does my Potterton boiler not come on?
The wall mounted control panel’s display inside is not showing … read more Sprinkler/irrigation system issueHunter PC-330iSee attached PDF doc with photosSystem will not come on. Display flashes very faintly, very … read more Vocational, Technical or Tra… I have an old Potteron profile boiler which today won’t fire up.
Once you are sure the electricity is off you can release the retaining clip which engages in a small slot. You will need to gently press the tongue in to pivot off the old EP2000. Simply reverse the procedure to refit the new EP programmer replacement.
Simple turn of the power to the central heating system and make sure you have isolated with the correct switch or fuse. Once you are sure the electricity is off you can release the retaining clip which engages in a small slot. You will need to gently press the tongue in to pivot off the old EP2000.
What kind of timer does Potterton boiler use?
Have a Potterton EP2 timer which replaced a EP2002 that the slider broke on. Ever since change hot water has to be on for boiler to fire up. Guy that did the swap says it’s the way the system is set up. (Appears to be gravity hot water, pumped CH).
Once you are sure the electricity is off you can release the retaining clip which engages in a small slot. You will need to gently press the tongue in to pivot off the old EP2000. Simply reverse the procedure to refit the new EP programmer replacement. The replacement EP clock is a fast to fit direct replacement which is simple to fit.
