How to install a diverter or transfer valve Kohler?

Apply thread sealant to the inlet port threads and connect the water supply to the valve inlet. Two-Way:If two accessories will be attached to the valve, go to the ″Two-Way Installation″ section. Three-Way:If three accessories will be attached to the valve, go to the ″Three-Way Installation″ section.

Where is the cotter pin on a Kohler transfer valve?

The K-728-K-NA valve allows for combined functions while the K-737-K-NA valve only allows for one function at a time. Note: The 3/4″ and 1/2″ Stacked Valves can be distinguished by the cotter pin located behind the stem of the top volume control. The 3/4″ valve has a cotter pin that looks like an “M” or “W”.

What do I need to install a transfer valve?

Install 1/2″ copper tubing or piping for all accessories. Securely fasten the piping and outlet ells to the framing. Install temporary 1/2″ nipples in the outlet ells so they extend a minimum of 2″ (51 mm) beyond the ﬁnished wall. Turn on the water supply to the valve and check for proper operation and leakage.

What does a 3 / 4 transfer valve look like?

The 3/4″ valve has a cotter pin that looks like an “M” or “W”. The 1/2″ has a cotter pin that looks like an “A” or “V”. Note: The Transfer and Diverter Valves can be distinguished easiest by looking at the mounting nut that holds the valve cartridge in place. The model number of the valve will be located on this nut.

How big is a shower diverter transfer valve?

It also can be used with body sprayers or jets. Installation process will be similar for other brands like : KOHLER, DELTA, DAZE, HANS GROHE and others. They may wary in shape and copper pipe size ½ or ¾ inch.

Why is my Kohler kitchen faucet not diverting to sidespray?

Sidespray trigger/button is broken . Sidespray diverter is worn: R eplace the diverter in the faucet. The part number of the diverter will vary depending on the faucet model number. Sidespray button is broken: Replace the entire sidespray. The part number of the sidespray will vary depending on the faucet model number.

Where do I find the diverter on my kitchen faucet?

To locate the diverter or sidespray part number for your faucet, enter your model number in the Find Parts search box (Fig. 1). (Fig. 1) On the faucet page, access the Interactive Parts Diagrams to locate and order the replacement diverter or sidespray.

How big of pipe do you need for Kohler rite temp valve?

Kohler Rite-Temp valves require 1/2″ copper pipe to connect the valve and the tub spout. If PEX is installed, a delayed flow of water may occur. The PEX will expand (thermal expansion) causing a slight delay in the flow of water getting to the tub spout or showerhead.

When did Kohler replace the k-305 shower valve?

The K-305 valve was discontinued June 2010 and replaced by the K-11748 valve. Excessive inlet pressure can also contribute to a leak or drip issue. If suspected, turn the pressure by adjusting the stops or installing a pressure reducing valve in the supply system.

Why did Kohler change the design of the mixer Cap?

Kohler changed the design of the Rite-Temp mixer cap in 2005 to prevent frustrations of the ‘boots and springs’ falling out of the valve. The previous version of the mixer cap had a removable section. If that section separated, the boots and springs could fall out of the valve causing mixing and leaking problems.

What to do if your Kohler shower valve is leaking?

Kohler shower valves occasionally require service. The first step in correcting a dripping or leaking valve is to identify the valve installed in your home. Assistance identifying the valve can be found in the “Identify a Single Control Bath/Shower Valve” article.