Can I connect plastic P-trap to metal?
Cast iron, PVC, ABS, steel or copper drain lines can easily be connected to your sink p-trap.
Can you use metal straps on PVC pipe?
So, the problem is far outweighed by consequences. As a former general contractor, none of my plumbers would use metal straps or ‘plumbers tape’ to support pvc pipe. I preferred to use pvc hanger straps myself, but plastic ‘plumbers tape’ is readily available and easier to use than metal..
How long should drain stubs be?
Like the supply stub-outs, the drain stub-out extends from a fitting — usually a sanitary tee — to a point 3 or 4 inches beyond the wall. The drain, which is usually 2-inch plastic pipe, maintains a minimum slope of 1/4 inch per foot from the stub-out to the point where it ties into a main waste pipe.
Can you use metal clamps on PVC conduit?
Use metal hangers with PVC conduit; they hold up better than plastic. Choose the single-hole type. One screw is more than enough support, and compared with the two-hole strap, installation will go twice as fast. PVC conduit, the maximum spacing between supports is 3 ft.
How often does PVC conduit need to be supported?
every 3 ft.
PVC must be supported every 3 ft. for trade sizes ½ inch through 1 inch. The support distance increases as the conduit size gets larger. For example, 2 inch PVC conduit can be supported every 5 ft; 6 inch PVC conduit can be supported every 8 ft.
How do you Plumb a drain stub out?
After turning off that line and cutting into it with a pipe cutter, you connect the pipe to the stub-out with an appropriate tee fitting. The drain stub-out represents two separate pathways. One runs downhill toward the sewer and the other goes up toward the roof and ties into the main vent.
Can a plastic sink drain pipe be connected to a metal pipe?
Connecting a plastic sink drain pipe to a metal pipe coming out of the wall will require a few basic tools, like an S trap. Connect a plastic sink drain pipe to a metal pipe coming out of the wall with help from a foreman for Lighty Contractors in this free video clip.
How do you attach PVC pipes to steel pipes?
Use your steel brush to do this. You will want to make sure to remove any dirt, dust, debris and grime that may be present. Doing this will ensure a solid attachment. Using your thread sealer, you will want to apply a generous amount to the male threads on the steel piping.
Can A P trap be attached to a galvanized stub?
The brass p-trap from the old sink was connected to the galvanized stub out as seen below. While there haven’t been any leaks that I’m aware of, the slip nut that attached the p-trap is broken so I want to replace the whole p-trap and connection.
After turning off that line and cutting into it with a pipe cutter, you connect the pipe to the stub-out with an appropriate tee fitting. The drain stub-out represents two separate pathways. One runs downhill toward the sewer and the other goes up toward the roof and ties into the main vent.
Can a PVC drain pipe connect to a P trap?
While moving the pedestal, the minor shocks completely broke the pipes going to p-trap and going to the wall. so I went to Home depot and bought new sink popup drain (pvc, expandable with chrome top, 1-1/4″) and new pvc p-trap (1-1/2″ because I thought the old chrome one was 1-1/2″)
How to connect a plastic sink to a metal pipe?
How to Connect a Plastic Sink Drain Pipe to a Metal Pipe Coming Out of : Water Pipes & Plumbing – YouTube How to Connect a Plastic Sink Drain Pipe to a Metal Pipe Coming Out of : Water Pipes & Plumbing If playback doesn’t begin shortly, try restarting your device.
How to connect PVC pipe to metal pipe?
Use fernco reducer rubber coupling and connect a 1-1/4 threaded on one side pipe to this wall pipe, buy another 1-1/4 p-trap and connect that p-trap to the pvc popup drain on inlet side and this metal threaded pipe on the outlet side. Does that seem right? Is there a better way? Remove that escution on the wall and lets have a look there.
