Are there replacement parts for Great Lakes spas?
Not as a guarantee of results. Great Lakes Spas Parts listed are NON- BRANDED equivalent parts ( Generic replacement parts ) from same part manufacture. Others are Replacements that will work as well or better. The listing is meant as a aid in helping you find your replacement parts faster. Not as a guarantee of results.
Is there a big list of Spa error codes?
Spa error codes can be somewhat cryptic, but when you have the BIG LIST of CODES, you can immediately define the two or three digit source of trouble. Problem is, there’s not much consistency among the error codes used by different spa pack manufacturers. Each company uses its own conventions for naming the various system faults.
Is there an error code for Leslie’s pool?
Leslie’s is proud to partner with Hot Tub Works to bring you this helpful content on lesliespool.com. The best thing about digital spas and hot tubs – those with a spa side control panel – is that you are given error codes for most equipment problems.
What are the messages on the spa topside panel?
Read our FAQ! Here are the common spa topside panel messages that you will encounter with your spa panel. The spa topside panel messages include common diagnostic messages, operational messages, and various other messages such as reminders.
Not as a guarantee of results. Great Lakes Spas Parts listed are NON- BRANDED equivalent parts ( Generic replacement parts ) from same part manufacture. Others are Replacements that will work as well or better. The listing is meant as a aid in helping you find your replacement parts faster. Not as a guarantee of results.
How big is the Great Lakes hot tub?
The largest Great Lakes Spa model, the GL8, was 90″ square with 60 jets and room for up to 8 persons. Contact us at [email protected] if you need assistance in finding the right spa part or accessory for your Emerald Spa hot tub – send details/part number/even a picture along with your request if you like.
What kind of heater does Great Lakes Spa use?
We offer every type of replacement heater for Great Lakes spas whether you have a Gecko or Balboa control system installed. For instance, we offer the Gecko IN.XE 4kW 240V heater. These are all factory original Emerald/Great Lakes replacement heaters.
Spa error codes can be somewhat cryptic, but when you have the BIG LIST of CODES, you can immediately define the two or three digit source of trouble. Problem is, there’s not much consistency among the error codes used by different spa pack manufacturers. Each company uses its own conventions for naming the various system faults.
Why is the heating element on my spa not working?
If for any reason one of these components fail then the required voltage to the coil will be jeopardized and the contactor will not close in order to send power to the heating element. As mentioned above, it is usually one of these components that will cause a spa not to heat.
When to replace the pressure switch on a hot tub?
Generally, if the pressure switch cannot be adjusted, it may need to be replaced – unless the problem is with the circuit board. The spa tech will start by using an ohmmeter (with the entire spa powered off) and will remove the 1 of the pressure switch wires. Then measure across the 2 terminals on the pressure switch.
When to open pressure switch on Balboa hot water heater?
Normal operating mode for a good pressure switch that is correctly adjusted is that the switch is CLOSED when the water is flowing through the heater and OPEN when the pump/heater stops. The Balboa system looks for the pump to be running when the pressure switch is CLOSED.
Can a pneumatic hot tub heater be replaced?
With no more than a few adjustments of your hot tub pack’s plumbing, our replacement spa controller/heaters will fit your spa . We carry both pneumatic (air-control) and electronic (digital) spa controller/heaters. Most older and budget spas came originally equipped with pneumatic spa controllers.
What is the OEM number for a gecko hot tub heater?
OEM part number C2400-0802A. This heater is found on some LA Spas and Gecko SSPA Control SpaGuts Universal Flo-Thru Heater Element is available in 4.0 or 5.5KW 220V, with selection for Incoloy (Non-Coated), or Titanium. Assembled in USA! An order includes ONE heater element, TWO
